服务热线: 400-117-8816
           13406879330

专注于扭剪型电动扳手、扭剪型手动扳手、定扭矩电动扳手、扭矩倍增器的研发与生产

热门关键词: 电动扳手能更快速地完成螺栓链接吗? 重型应用螺栓完成平安快速扭紧和拆卸的处理计划 工地用的电动扳手哪里有卖的,哪家质量好? 电动扭矩扳手必需恪守的硬性规则

当前位置:首页>技术文献>电动扳手好用吗?电动扳手的选择

电动扳手好用吗?电动扳手的选择

来源:http://www.xjnwz.com 日期:2019-06-04 发布人:admin

  电动扳手好用吗?电动扳手的选择

  Is Electric Spanner Useful? Selection of Electric Spanner电动扳手是给电源或蓄电池供电的扳手,是拧紧螺栓的工具。
  Electric wrench is a wrench for power supply or battery power supply. It is a tool for tightening bolts.
  主要用于钢结构安装行业,专门安装钢结构高强螺栓,高强螺栓是用来连接钢结构的接触面,通常采用螺栓组的方式。
  Mainly used in the steel structure installation industry, special installation of steel structure high-strength bolts, high-strength bolts are used to connect the contact surface of steel structure, usually using the way of bolt group.
  1、拉扳手用力要柔和均匀。永远不要用短的冲力拉,因为一个猛拉会产生一个冲力,螺栓或螺栓可能在力停止的那一刻扭过头了。
                          电动扭矩扳手
  1. Pull the wrench gently and evenly. Never pull with a short impulse, because a sharp pull produces an impulse, and a bolt or bolt may turn too far at the moment when the force stops.
  2. 污染物会阻碍精确的扭矩值。如果部件和螺孔中有污染物,则不可能获得正确的扭矩值。
  2. Pollutants can hinder accurate torque values. If there are contaminants in the components and screw holes, it is impossible to obtain the correct torque value.
  摩擦是一种普遍现象,但也有好的和坏的影响。好的部分是把这些部分放在一起;不好的一面是,当收紧时,可能会导致错误的结果。机械工人用手拧紧连接时,只有10%到20%的力是用来拧紧的。在许多情况下,40%到50%的扭矩用于克服螺栓头和部件之间的摩擦。拧紧螺栓时应考虑所有这些摩擦因素和其他因素。
  Friction is a common phenomenon, but it has both good and bad effects. The good part is to put these parts together; the bad part is that when tightening, it can lead to wrong results. When the mechanic tightens the connection by hand, only 10% to 20% of the force is used to tighten it. In many cases, 40% to 50% of the torque is used to overcome friction between the bolt head and components. All these friction and other factors should be taken into account when tightening bolts.
  4. 当拧紧带有损坏或堵塞螺纹的螺母或螺栓时,请注意通过损坏区域需要多少额外扭矩,并将此额外扭矩应用于建议的扭矩值。
  4. When tightening nuts or bolts with damaged or blocked threads, pay attention to how much additional torque is required to pass through the damaged area and apply this additional torque to the recommended torque value.